Regulation No 1 of the Economic Commission for Europe of the United Nations (... (42010X0710(01))
Regulation No 1 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of motor vehicle headlamps emitting an asymmetrical passing beam and/or a driving beam and equipped with filament lamps of category R2 and/or HS1
- Regulation No 1 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of motor vehicle headlamps emitting an asymmetrical passing beam and/or a driving beam and equipped with filament lamps of category R2 and/or HS1
- SCOPE(1)
- 1. DEFINITIONS
- 2. APPLICATION FOR APPROVAL
- 3. MARKINGS(3)
- 4. APPROVAL
- 4.1. General
- 4.2. Composition of the approval mark
- 4.3. Arrangement of the approval mark
- 4.3.1. Independent lamps
- 4.3.2. Grouped, combined or reciprocally incorporated lamps
- 5. GENERAL SPECIFICATIONS
- 6. ILLUMINATION
- 7. GAUGING OF DISCOMFORT
- 8. STANDARD HEADLAMP
- 9. CONFORMITY OF PRODUCTION
- 10. PENALTIES FOR NON-CONFORMITY OF PRODUCTION
- 11. MODIFICATION AND EXTENSION OF APPROVAL OF A TYPE OF HEADLAMP
- 12. PRODUCTION DEFINITELY DISCONTINUED
- 13. NAMES AND ADDRESSES OF TECHNICAL SERVICES RESPONSIBLE FOR CONDUCTING APPROVAL TESTS AND OF ADMINISTRATIVE DEPARTMENTS
- 14. TRANSITIONAL PROVISIONS
- ANNEX 1
- COMMUNICATION
- (maximum format: A4 (210 × 297 mm))
- ANNEX 2
- Special headlamps for agricultural or forest tractors and other slow-moving vehicles
- ANNEX 3
- Minimum requirements for conformity of production control procedures
- 1. GENERAL
- 2. MINIMUM REQUIREMENTS FOR VERIFICATION OF CONFORMITY BY THE MANUFACTURER
- 2.1. Nature of tests
- 2.2. Methods used in tests
- 2.3. Nature of sampling
- 2.4. Measured and recorded photometric characteristics
- 2.5. Criteria governing acceptability
- ANNEX 4
- Tests for stability of photometric performance of headlamps in operation
- 1. TEST FOR STABILITY OF PHOTOMETRIC PERFORMANCE
- 1.1. Clean headlamp
- 1.1.1. Test Procedure
- 1.1.1.2. Test voltage
- 1.1.2. Test results
- 1.1.2.1. Visual inspection
- 1.1.2.2. Photometric test
- 1.2. Dirty headlamp
- 1.2.1. Preparation of the headlamp
- 1.2.1.1. Test mixture
- 1.2.1.2. Application of the test mixture to the headlamp
- 1.2.1.3. Measuring equipment
- 2. TEST FOR CHANGE IN VERTICAL POSITION OF THE CUT-OFF LINE UNDER THE INFLUENCE OF HEAT
- 2.1. Test
- 2.2. Test results
- ANNEX 5
- EXAMPLES OF ARRANGEMENTS OF APPROVAL MARKS
- (See paragraph 4 of this Regulation)
- Figure 1
- Figure 3b
- Simplified marking of grouped, combined or reciprocally incorporated lamps
- Figure 10
- MODEL A
- MODEL B
- MODEL C
- MODEL D
- Figure 11
- Lamp reciprocally incorporated with a headlamp
- Example 1
- Example 2
- ANNEX 6
- MEASURING SCREENS
- A. Headlamp for right-hand traffic
- (Dimensions in mm)
- B. Headlamp for left-hand traffic
- (Dimensions in mm)
- C. Measuring points of illumination values
- ANNEX 7
- Requirements for lamps incorporating lenses of plastic material — testing of lens or material samples and of complete lamps
- 1. GENERAL SPECIFICATIONS
- 2. TESTS
- 2.1. Resistance to temperature changes
- 2.1.1. Tests
- 2.1.2. Photometric measurements
- 2.1.2.1. Method
- 2.1.2.2. Results
- 2.2. Resistance to atmospheric and chemical agents
- 2.2.1. Resistance to atmospheric agents
- 2.2.2. Resistance to chemical agents
- 2.2.2.1. Test mixture
- 2.2.2.2. Application of the test mixture
- 2.2.2.3. Cleaning
- 2.2.3. Results
- 2.3. Resistance to detergents and hydrocarbons
- 2.3.1. Resistance to detergents
- 2.3.2. Resistance to hydrocarbons
- 2.3.3. Results
- 2.4. Resistance to mechanical deterioration
- 2.4.1. Mechanical deterioration method
- 2.4.2. Results
- 2.5. Test of adherence of coatings, if any
- 2.5.1. Preparation of the sample
- 2.5.2. Description of the test
- 2.5.3. Results
- 2.6. Tests of the complete lamp incorporating a lens of plastic material
- 2.6.1. Resistance to mechanical deterioration of the lens surface
- 2.6.1.1. Tests
- 2.6.1.2. Results
- 2.6.2. Test of adherence of coatings, if any
- 3. VERIFICATION OF THE CONFORMITY OF PRODUCTION
- APPENDIX 1
- CHRONOLOGICAL ORDER OF APPROVAL TESTS
- APPENDIX 2
- Method of measurement of the diffusion and transmission of light
- 1. EQUIPMENT (see figure)
- 2. MEASUREMENTS
- APPENDIX 3
- SPRAY TESTING METHOD
- 1. TEST EQUIPMENT
- 1.1. Spray gun
- 1.2. Test mixture
- 2. TEST
- APPENDIX 4
- ADHESIVE TAPE ADHERENCE TEST
- 1. PURPOSE
- 2. PRINCIPLE
- 3. SPECIFIED ATMOSPHERIC CONDITIONS
- 4. TEST PIECES
- 5. PROCEDURE
- 6. RESULTS
- ANNEX 8
- MINIMUM REQUIREMENTS FOR SAMPLING BY AN INSPECTOR
- 1. GENERAL
- 2. FIRST SAMPLING
- 2.1. The conformity is not contested
- 2.1.1.1. sample A
- 2.1.1.2. sample B
- 2.2. The conformity is contested
- 2.2.1.1. sample A
- 2.2.1.2. sample B
- 2.3. Approval withdrawn
- 2.3.1. sample A
- 2.3.2. sample B
- 3. REPEATED SAMPLING
- 3.1. The conformity is not contested
- 3.1.1.1. sample C
- 3.1.1.2. sample D
- 3.2. The conformity is contested
- 3.2.1.1. sample D
- 3.3. Approval withdrawn
- 3.3.1. sample C
- 3.3.2. sample D
- 4. CHANGE OF THE VERTICAL POSITION OF THE CUT-OFF LINE
- Figure 1
Feedback