Regulation No 69 of the Economic Commission for Europe of the United Nations ... (42010X0731(01))
Regulation No 69 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of rear marking plates for slow-moving vehicles (by construction) and their trailers
- Regulation No 69 of the Economic Commission for Europe of the United Nations (UN/ECE) — Uniform provisions concerning the approval of rear marking plates for slow-moving vehicles (by construction) and their trailers
- 1. SCOPE
- 2. DEFINITIONS(2)
- 2.2. Retro-reflection
- 2.3.12. Angle of rotation ε
- 2.4. Definition of photometric terms
- 2.4.1. Coefficient of retro-reflection R’
- 2.5. Fluorescence
- 2.6. Description of goniometer
- 2.7. Definition of ‘type’
- 3. APPLICATION FOR APPROVAL
- 4. MARKINGS
- 5. APPROVAL
- 6. GENERAL SPECIFICATIONS
- 7. SPECIAL SPECIFICATION (TESTS)
- 8. MODIFICATIONS AND EXTENSION OF APPROVAL OF REAR MARKING PLATES FOR SLOW-MOVING VEHICLES (BY CONSTRUCTION) AND THEIR TRAILERS
- 9. CONFORMITY OF PRODUCTION
- 10. PENALTIES FOR NON-CONFORMITY OF PRODUCTION
- 11. PRODUCTION DEFINITELY DISCONTINUED
- 12. TRANSITIONAL PROVISIONS
- 13. NAMES AND ADDRESSES OF TECHNICAL SERVICES RESPONSIBLE FOR CONDUCTING APPROVAL TESTS, AND OF ADMINISTRATIVE DEPARTMENTS
- ANNEX 1
- THE CIE CO-ORDINATE SYSTEM
- Figure 1
- Figure 2
- ANNEX 2
- COMMUNICATION
- (Maximum format: A4 (210 × 297 mm))
- ANNEX 3
- ARRANGEMENT OF THE APPROVAL MARK
- ANNEX 4
- TEST PROCEDURE
- TEST SAMPLES
- ANNEX 5
- SPECIFICATIONS OF SHAPE AND DIMENSIONS
- SHAPE AND DIMENSIONS OF RETRO-REFLECTIVE/FLUORESCENT (CLASS 1) OR RETRO-REFLECTIVE ONLY (CLASS 2) SMV REAR MARKING PLATES
- 1. Shape
- 2. Pattern
- 3. Dimensions
- ANNEX 6
- COLORIMETRIC SPECIFICATIONS
- 2. Red retro-reflective material or devices
- 3. Red fluorescent material
- ANNEX 7
- PHOTOMETRIC SPECIFICATIONS
- PHOTOMETRIC PROPERTIES
- ANNEX 8
- RESISTANCE TO EXTERNAL AGENTS
- 1. RESISTANCE TO WEATHERING
- 2. RESISTANCE TO CORROSION (ISO Standard 3768)
- 3. RESISTANCE TO FUELS
- 4. BONDING STRENGTH (in the case of adhesive materials)
- 5. RESISTANCE TO WATER
- 6. RESISTANCE TO IMPACT (except for plastics corner-cube reflectors)
- 7. RESISTANCE TO CLEANING
- 7.1. Manual cleaning
- 7.2. Power washing
- ANNEX 9
- RESISTANCE TO HEAT
- ANNEX 10
- RIGIDITY OF THE PLATES
- ANNEX 11
- Stability in time of the optical properties
- (1)
- of rear marking plates
- ANNEX 12
- Rear marking plates for slow-moving vehicles and their trailers
- Example
- ANNEX 13
- Minimum requirements for conformity of production control procedures
- 1. GENERAL
- 2. MINIMUM REQUIREMENTS FOR VERIFICATION OF CONFORMITY BY THE MANUFACTURER
- 2.1. Nature of tests
- 2.2. Methods used in tests
- 2.3. Nature of sampling
- 2.4. Measured and recorded photometric characteristics
- 2.5. Criteria governing acceptability
- ANNEX 14
- MINIMUM REQUIREMENTS FOR SAMPLING BY AN INSPECTOR
- 1. GENERAL
- 2. FIRST SAMPLING
- 2.1. The conformity is not contested
- 2.2. The conformity is contested
- 2.3. Approval withdrawn
- 3. REPEATED SAMPLING
- 3.1. The conformity is not contested
- 3.2. The conformity is contested
- 3.3. Approval withdrawn
- 4. RESISTANCE TESTS
- Figure 1
- ANNEX 15
- Guidelines for installation of rear marking plates on slow-moving vehicles (by construction) and their trailers
- 2. Scope
- 3. Number
- 4. Arrangement
- 5. Position
- 6. Geometric visibility
Feedback